ASTM B(). Standard Specification for Precipitation Hardening Nickel- Copper-Aluminum Alloy (UNS N) Bar, Rod, Wire. ASTM B Round Bar is a precipitation-hardenable nickel-copper material that combines the excellent corrosion resistance characteristic of Monel with the . Aesteiron leading Monel K ASTM B Rod manufacturers, have wide range of ASTM F, ASTM B, ASTM B Round Bar & ASTM B Rod.
|Published (Last):||1 November 2004|
|PDF File Size:||10.37 Mb|
|ePub File Size:||3.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM B865 – 04(2015)
Rounded Unit for Observed or Calculated Value Chemical composition, hardness, Nearest unit in the last right-hand place and tolerances when expressed in of? Dry, astmm, or water-base coolant. Grind brazed tools as for finish turning and facing except back rake may be best at 0 degrees. C-2 grade not recommended, but tipped drills may be successful on rigid setup if no great depth. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. In case of dissatisfaction with the results of the test, the manufacturer or supplier may make claim for a rehearing.
Dimensions and Permissible Variations 7.
Our company has gained recognition globally for the excellence of our services and quality of the products we supply. Number of Tests Tests need not be repeated when unaged material from the same heat can be identi?
Monel K Round Bars is a nickel-chromium alloy bar that contains supplemental amounts of columbium, iron, molybdenum, aluminum, and titanium.
MONEL K500 (UNS N05500)
Coolant-feed carbide tipped drills may be economical in some setups. Mill age-hardened products have been precipitation heat treated by the manufacturer and further thermal treatment is not normally required. Oil or water-base coolants will reduce thermal shock damage. Users of this standard are expressly advised that determination of zstm validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
For each multiple, an allowance of 1? For material in straightened and cut lengths, deduct 15 ksi MPa from above values. Change n865 sharpened tools at regular intervals rather than out of necessity.
B — 04 specimens shall be prepared in accordance with Test Methods E 8 for rectangular bar up to asfm Shop air or any oxygen bearing gases should be avoided when plasma cutting these alloys.
ASTM B 沉淀硬化镍铜铝合金(UNS N)棒,条,丝,锻件_百度文库
Turning or Facing C-2 and C-3 grade: Oil or waterbase coolants will reduce thermal shock damage of carbide cutter teeth. D Age hardening heat astmm A viscosity at degree F from 50 to SSU. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Sstm Headquarters. Heavy machining n865 this alloy is best accomplished when the material is in the annealed condition or hot-worked and quenched condition.
The specimen shall ast, aged, or annealed and aged, as required by either applicable Table 5 or Table 6. Mill age-hardened products have been precipitation heat treated by the manufacturer and further thermal treatment normally is not required. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Siddhagiri Metals and Tubes Rating: Rejection and Rehearing Alloy K has approximately three times the yield strength and double the tensile strength when compared with alloy From pure water to non-oxidising mineral acids, salts and alkalis.
Tensile strength and yield strength nearest psi 6. ASTM does not give any warranty express or implied or make any adtm that the contents of this abstract are accurate, complete or up to date. MONEL K retains the excellent corrosion resistant characteristics of and has enhanced strength and hardness after precipitation hardening when compared with